![]() ![]() Whenever either a MAIN TERM or a Sub-term appears in a Derwent title, only the corresponding MAIN TERM is posted to the online file as a Title Term. All given derivatives of a Title Term are collected under a MAIN TERM. Introduction Derwent Title Terms are used to simplify word searching of Derwent titles, and to optimise the thoroughness of such searches. Searchable Preferred Forms of Title Words No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, mechanical, recording, photocopying or otherwise – without express written permission from the copyright / Visit the Derwent web site at Revised Edition 4 published February 2000 ISBN: 0 901157 23 6 (Edition 4 revised) All rights reserved. Published by Derwent Information 14 Great Queen Street, London WC2B 5DF, United Kingdom Visit the Thomson Scientific web site at © 2000 Thomson Derwent The PDFs can be printed on legal sized paper, landscape format.2000 Thomson Published by Thomson Scientific 14 Great Queen Street, London WC2B 5DF, United Kingdom Instructions can be printed in landscape format on legal-sized paperĭownload Instruction Sheets in PDF, for select project applications, below. Like anything the more maintenance you do will add to the longevity of the product. Securely fasten the rubber to the deck boards with corrosion-resistant screws.īrush-treat raw wood that is exposed when cutting and retreat the tops of the boards with a good brushing of water repellent every year. To get the best performance out of your deck you should treat the wood by applying a coat of water repellent treatment onto all surfaces before installation. Freshly treated boards could be snug, and may require tapping with a rubber mallet to fit into the channels. ![]() Freshly treated deck boards may swell and shrink, as it dries out. The MultyDeck™ base is engineered to hold 3 decking boards. Add 2 × 2” wood trim to deck perimeter using 3” screws. Remove outer side supports of rubber base using utility knife or circular saw. The frame can add another level of stability to the structure, but it is not needed for utilitarian applications such as platforms for storage. Insert board between each set of panels to increase width and secure wood to base, using 1 3/4 to 2" deck screws to go into side supports of rubber base at a 30 degree angle.įully joined, the final deck can be finished with a frame to create a clean look. Fasten into place, on either side of the joiner board, by screwing the wood at a 45 degree angle into the rubber side supports of the base on each opposing panel. Add the joiner boards to the spaces between panels. Joiner boards are simply additional 2圆" decking boards, same as those secured to MultyDeck rubber bases. Leave a gap of 5 ½" between rubber base, this will form the groove that will accept the joiner boards. Arrange the panels to cover the desired deck space. Turn the panels over so that the rubber bases are now on the ground. You will need 6 deck screws per rubber base (2 screws per board, each base holds three boards). Insert screws at center of each rubber base to secure wood firmly. Press rubber bases at recommended spacing of maximum 18" between bases. Attach boards to rubber base with 1 ⅝" deck screws. If the deck is being installed on flat, clear and even concrete, such as a poolside deck or a commercial space such as a restaurant patio, there is no ground prep required.īuild panels using the rubber bases as guides to hold 6" decking boards or composite boards. It is recommended to use a landscape fabric over the prepared ground (especially sod or active vegetation areas) to prevent growth of plants through the deck boards later in the season. The MultyDeck™ bases can be assembled on virtually any type of surface including dirt or sand, gravel, sod, or cracked pavement. To prepare the ground, first measure the layout and shape of the deck with a hose or string and add or remove ground material until a flat surface is achieved. Other equipment that will be needed for deck installation projects:Īlways ensure ground surface is levelled before installing deck This will drastically reduce the risk of eye and hand injury. Always wear safety glasses, and protect your hands by wearing all-purpose utility gloves. Build easy-to-install decks quickly and simply:Ī lways wear safety googles and protective glovesĪs in all construction projects, remember to use the correct personal protective equipment. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |